Alwarerc ALware Quad Flyer Spider 500 ( Kit Only ) Bedienungsanleitung

ALware Quad Flyer Spider 500X With Lighting SystemInstruction Manualwww.alwarerc.com

Step 21.Next insert the Motor Mount into another side of the Spider Arm at first.Step 22.Twist a M2x8 Hex Cap Screw into the Alu Rod under the Motor M

Step 25.Hook one end of the Tension Spring to the Landing Gear installed on the Spider Arm Set. (Remarks: the hooking direction of the Spring is uniqu

Step 29.A Complete Spider Arm Set is finished.Step 30.Repeat step 5-29 to complete total four sets of Spider Arms.Step 31.Prepare 2x Central Frames, 4

Step 33.Insert a Spider Arm Set onto the trough of the Central Frame. (Remarks: the assembly direction is unique and important!)Step 34.Close view of

Step 37.Second close view of step 35.Step 38.Repeat step 33-37 to secure other three Spider Arm Sets onto the Central Frame.(Remarks: the Landing Gear

Step 41.Close view of step 40.Step 42.Next, rotate the Spider Arm Set according to the red arrow direction(counter-clockwise) until the Hex Alu Rod in

Step 45.Close view after step 44.Step 46.Prepare 4x Round Alu Rod 35mm and 4x M2x8mm Hex Cap Screws to get ready to secure the Alu Rod onto the four 2

Step 49.Oppose view of step 48.Step 50.Set the Spider Arms for flying status (un-folded) and place all the connectors of four ESCs as the photo shown

Step 53.Red arrow indicate the forwards flying direction of Spider 500X. Suggested setting of LED lighting system: Blue LEDs will be placed on the fro

Step 57.Close view of step 56.Step 58.Apply little amount of CA glue/ Tap to secure the LEDs.Step 59.Completed Spider Arm with LED lighting system ins

Introduction:A novel, manoeuvrable and marvelous Quad Flyer Spider 500X is now released from ALWARE design company! Spider 500X was designed based on

Step 61.Repeat step 54-60 to install the LED light system to the rest of the Spider Arm Sets. Next, fix the wires onto the Central Frame with Taps. Th

Step 65.Repeat step 63-64 to hook the other Tension Springs to the rest of the Spider Arms and secure the other end of the Tension Springs onto the M2

Step 69.Insert the Damper Rod(short) in between the servo ear and the Central Frame, then secure the servo with a M2x18 Hex Cap Screw and a M2 Nut.Ste

Step 73.Insert one Eye Frame onto the Central Frame. (Remarks: the assembly direction of the Eye Frames will change the expression of your Spider 500X

Step 77.Tie your 3 cells Lipo battery(not included) onto the Central Frame with the battery strap. (Remarks: the battery connector need to be placed o

Step 81.Prepare 8x M2x6 Hex Cap Screws and 8x Washers 2x5x0.5mm.Step 82.Twist M2x6 Hex Cap Screw with Washer into the Hex Alu Rod installed on the Spi

Step 85.Twist M2x8 Hex Cap Screw into the Round Alu Rod 35mm installed on the Spider Arm to secure the two Central Frames together.Step 86.Repeat step

Step 89.Battery installation method 2: under the Spider 500X body.Step 90.Add some lubricating oil or grease on each troughs on both of the two Centra

Step 93.Thirdly, rotate the Spider Arm 4 in counter-clockwise direction. The Spider Arm 4 is now be folded.Step 94.Unfold and fold(step 93) the Spider

Step 97.Unfold and fold(step 96) the Spider Arm for 4-5 times, and the Collapsible System will become smoother. Repeat Step 95 – 97 for Spider Arm 1.S

Parts List:A: Spider Arm Frames x8B: Arm Ribs x8C: Landing Gears x4D: Motor Mounts x4E: Central Frames x2F: Eye Frames x2G: Screw Package x1H: FPV Pa

Step 101.Secure the motor onto the Motor Mount using 2x M3x4 Hex Cap Screws. Step 102.Install the FPV mount onto the servo installed on the Central Fr

Battery Mounting Method 2: Under the Central Frame(suitable for larger size Lipo batteries).End of Assembly Instructionwww.alwarerc.com

Setting Illustration: The following setting data is just for reference as with different Gyros and equipment , different settings will be requested.T

G2:-Tension Spring 0.6x4.9x18mm x4pcs-Tension Spring 0.6x4.9x22mm x4pcs-3x7x3mm Flange Bearing x4pcs-M2 Nut x2pcs-M3 Nut x4pcs-Washer 2x5x0.5mm 18pcsG

Assembly Instruction Steps:Step 1.Prepare 1x Landing Gear, 1x (3x7x3mm)Flange Bearing, 1x M3x8 Hex Cap Screw and 1x M3 Nut.Step 2.Insert the M3x8 Hex

Step 5.Prepare 2x Spider Arm Frames, 2x Hex Alu Rod 39mm, 5x Round Alu Rod 35mm, 4x M2x6 Hex Cap Screws and 5x M2x8 Hex Cap Screws.Step 6.Secure a Hex

Step 9.Secure 5 pieces of Round Alu Rod 35mm to the either side of the Spider Arm Frame with 5pcs M2x8 Hex Cap Screws. (Remarks: the assembly directio

Step 13.Bend and insert an Arm Rib onto the upper side of the Spider Arm Set.Step 14.The end side of the Arm Rib with a small hole should be placed op

Step 17.Insert the second Arm Rib onto the lower side of the Spider Arm Set. The end side of the Arm Rib with a small hole should be placed oppose to